All products ship from our 30,000 sq. ft. Haverhill, MA warehouse
Panasonic MCO-19AICUVH-PA CO₂ Incubator
The Panasonic MCO-19AICUVH-PA CO₂ Incubator is a 170-liter (6.0 cu. ft.) cell culture incubator designed for laboratories that require precise environmental control combined with advanced contamination protection. Featuring infrared CO₂ monitoring, direct heat and air-jacket temperature control, copper-enriched stainless steel construction, SafeCell UV technology, and an integrated H₂O₂ decontamination system, the MCO-19AICUVH-PA is particularly well suited for sensitive cell culture and demanding biotechnology and pharmaceutical research applications.
Available used and refurbished from American Instrument Exchange, this Panasonic CO₂ incubator provides a full-size chamber with the environmental stability required for routine and advanced cell culture. Its combination of a 0–20% CO₂ range, temperatures up to 50°C, approximately 95% relative humidity, rapid environmental recovery, and multiple contamination-control technologies makes it a versatile choice for laboratories where both culture consistency and chamber cleanliness are priorities.
Key Features
170 L (6.0 cu. ft.) cell culture chamber
Temperature range from 5°C above ambient to 50°C
±0.25°C temperature uniformity at 37°C
0–20% CO₂ control range
Infrared CO₂ sensor with continuous auto-zero calibration
Direct Heat and Air Jacket temperature-control system
Copper-enriched stainless steel interior
SafeCell UV contamination-control system
H₂O₂ vapor decontamination capability
Approximately 95% relative humidity at 37°C
Four adjustable shelves supplied in the standard configuration
Professionally inspected and tested by American Instrument Exchange
90-day warranty included
Panasonic MCO-19AICUVH-PA CO₂ Incubator Overview
The Panasonic MCO-19AICUVH-PA combines a full-size culture chamber with multiple systems designed to maintain consistent incubation conditions while controlling contamination. Its 170-liter chamber provides enough capacity for routine research and higher-volume cell culture without requiring the footprint of a larger reach-in system.
Panasonic's Direct Heat and Air Jacket system uses controlled heating zones and fan-assisted circulation to promote uniform temperatures throughout the chamber. At a 37°C setpoint, temperature uniformity is specified at ±0.25°C under defined operating conditions. The incubator's PID-controlled system allows temperatures to be maintained from approximately 5°C above ambient to 50°C.
CO₂ is regulated from 0–20% using a ceramic-based infrared sensor with dual-wavelength measurement and continuous auto-zero calibration. Infrared sensing provides fast response to changes in chamber conditions and is particularly useful in humidified incubators where reliable CO₂ measurement is essential for maintaining media pH.
The MCO-19AICUVH-PA is especially notable for its contamination-control design. Rather than relying on a single approach, Panasonic combines a copper-enriched stainless steel interior, UV exposure, and H₂O₂ vapor decontamination to provide multiple layers of protection for laboratories maintaining valuable or contamination-sensitive cultures.
Common Applications
The Panasonic MCO-19AICUVH-PA is suitable for a broad range of life science applications, including mammalian cell culture, stem cell research, cancer research, immunology, vaccine development, tissue engineering, regenerative medicine, pharmaceutical research, biotechnology, cell biology, and other applications requiring precise control of temperature, CO₂, and humidity.
Its advanced contamination-control capabilities can be particularly valuable in laboratories maintaining sensitive primary cells, valuable cell lines, or long-duration cultures where an unexpected contamination event can result in substantial loss of research time and materials.
The Panasonic MCO-19AICUVH-PA provides the environmental range required for many routine and advanced mammalian cell culture protocols. Its 170-liter chamber and adjustable shelving make it suitable for laboratories maintaining several culture types or experiments simultaneously.
Common Cell Types
Mammalian cell lines
Primary cells
Stem cells
Fibroblasts
Epithelial cells
Immune cells
Hybridoma cultures
Cancer cell lines
Cell lines used in biotechnology and pharmaceutical research
Typical Culture Vessels
T-flasks
Multiwell plates
Cell culture dishes
Petri dishes
Suspension culture flasks
Media bottles
Other standard culture vessels compatible with the shelving
Four 17.7 × 17.7-inch shelves are supplied in the standard configuration, with the chamber capable of accepting additional shelving when appropriate. This allows laboratories to adapt the interior layout to changing research requirements rather than dedicating the incubator to one particular vessel format.
Environmental Control & Contamination Protection
Contamination prevention is one of the strongest reasons to consider the MCO-19AICUVH-PA. The incubator uses several complementary technologies rather than depending exclusively on periodic manual chamber cleaning.
The interior and shelves are manufactured from copper-enriched stainless steel, providing the durability and cleanability of stainless steel while incorporating copper into surfaces throughout the culture chamber. The SafeCell UV system adds active contamination control by exposing air and water in the humidification system to ultraviolet light while cultures remain protected from direct UV exposure.
The UVH configuration adds H₂O₂ vapor decontamination, allowing the interior chamber and associated components to undergo an in-situ decontamination cycle. This provides laboratories with a more comprehensive method of chamber decontamination following a contamination event, between critical projects, or as part of an established preventative maintenance protocol.
Environmental stability is equally important. The Direct Heat and Air Jacket system combines controlled heating with gentle fan-assisted airflow to promote uniform temperatures throughout the chamber. CO₂ concentration is continuously monitored by an infrared sensor, while natural evaporation from the humidifying pan maintains approximately 95% relative humidity at 37°C to help minimize evaporation from culture media.
Together, these systems make the MCO-19AICUVH-PA particularly attractive for laboratories where both reproducible environmental conditions and aggressive contamination management are important to successful cell culture.
Infrared, dual-wavelength with auto-zero calibration
CO₂ Deviation
±0.15% at 37°C and 5% CO₂ under specified conditions
Relative Humidity
Approximately 95% RH at 37°C
Humidification
Natural evaporation with humidifying pan
Heating System
Direct Heat and Air Jacket
Interior Material
Copper-enriched stainless steel
Contamination Control
SafeCell UV + H₂O₂ decontamination
Inner Door
Tempered glass
Shelves
4 standard; up to 15 supported
Shelf Dimensions
17.7"W × 17.7"D
Shelf Capacity
15.4 lb. (7 kg) each
Interior Dimensions (W × D × H)
19.3" × 20.6" × 26.2"
Exterior Dimensions (W × D × H)
24.4" × 27.9" × 35.4"
Access Port
30 mm rear access port
CO₂ Supply Pressure
Approximately 5 psi
Electrical
115V, 60 Hz, single phase
Maximum Power Consumption
310 W
Net Weight
Approximately 205 lb. (93 kg)
Specifications are based on manufacturer literature and may vary according to production date and configuration. Confirm the specifications and included accessories of the individual incubator before purchase.
What is the difference between the MCO-19AICUVH-PA and MCO-19AICUV-PA?
Both versions incorporate Panasonic's infrared CO₂ control, copper-enriched stainless steel interior, and SafeCell UV system. The MCO-19AICUVH-PA additionally incorporates H₂O₂ vapor decontamination capability, providing another level of contamination control for demanding cell culture applications.
How does the H₂O₂ decontamination system benefit a cell culture laboratory?
The system allows the chamber to undergo in-situ hydrogen peroxide vapor decontamination without relying solely on manual cleaning. This can be particularly valuable following suspected contamination or between sensitive research projects where a more comprehensive chamber decontamination procedure is desired.
Does the Panasonic MCO-19AICUVH-PA use an infrared CO₂ sensor?
Yes. The incubator uses a ceramic-based infrared CO₂ sensor with dual-wavelength measurement and continuous auto-zero calibration. This provides stable CO₂ monitoring across routine cell culture conditions.
Is the MCO-19AICUVH-PA suitable for stem cell culture?
Its precise temperature and CO₂ control, high-humidity chamber, and extensive contamination-control features can make the MCO-19AICUVH-PA a strong option for stem cell and other sensitive cell culture applications. Laboratories should always verify that their specific culture protocol falls within the incubator's operating specifications.
How large is the Panasonic MCO-19AICUVH-PA?
The incubator provides 170 L (6.0 cu. ft.) of chamber capacity. Exterior dimensions are approximately 24.4 inches wide × 27.9 inches deep × 35.4 inches high, making it a full-size laboratory CO₂ incubator that can still be incorporated into many benchtop or stacked installations.
Is this Panasonic CO₂ incubator refurbished?
Yes. Used Panasonic MCO-19AICUVH-PA incubators offered by American Instrument Exchange are inspected and tested prior to shipment and include a 90-day warranty. Included shelves, accessories, and individual configurations should be confirmed for the specific unit available.
Click Hereto see the Panasonic MCO-19AICUVH CO2 incubator on the American Instrument Exchange YouTube channel.
Click Hereto read a review of this product on our blog!
Testing Procedures for Used and Refurbished Laboratory Incubators Ensure Quality and Stability Before Use
Used and refurbished laboratory incubators from American Instrument Exchange are thoroughly tested to ensure optimal performance and temperature stability with laboratory safety standards. Each unit undergoes a detailed inspection and functionality assessment to meet the needs of research, clinical, and industrial labs.
Why Testing Used Laboratory Incubators Is Essential
Before a laboratory incubator is reintroduced into any work environment, it must be tested for:
• Temperature uniformity and accuracy
• Airflow and humidity control (if applicable)
• Door seal integrity and insulation effectiveness
• Electrical and safety system compliance
Comprehensive testing reduces the risk of culture loss, contamination, and equipment failure—especially critical in applications involving cell culture, microbiology, pharmaceutical research, and diagnostics.
Our multi-point testing protocol for used and refurbished incubators ensures reliability, safety, and performance across all models and brands.
Key Testing Procedures for Refurbished and Used Laboratory Incubators
1. Initial Visual Inspection
• Check for cosmetic damage, corrosion, and wear to exterior surfaces, door hinges, and gasket seals
• Inspect power cord, wiring, and display panel for any defects or signs of tampering
• Confirm that shelves, chamber components, and internal fixtures are present and undamaged
2. Functional Testing
• Power on the incubator and verify all display indicators and alarms function correctly
• Test door latch and seal mechanisms for proper closure and insulation
• Run basic temperature cycles to ensure the unit maintains stability over time
3. Temperature Accuracy and Uniformity Tests
• Test internal sensors and controllers using temperature probes
• Measure temperature consistency at multiple chamber locations over several hours
• Confirm that programmable temperature settings respond accurately
4. Airflow and Humidity Control (if applicable)
• Test internal fan operation and airflow distribution
• For humidified incubators, inspect and test humidity reservoirs, sensors, and control systems
• Check for condensation buildup and confirm environmental stability
5. Electrical Safety and Compliance Checks
• Ensure all electrical components are properly grounded
• Perform insulation resistance and leakage current tests
• Verify compliance with current electrical safety standards for laboratory equipment
6. Final Quality Assurance Checklist
• Perform full cycle testing at various temperature setpoints
• Document performance benchmarks and results
All refurbished incubators from American Instrument Exchange are backed by our commitment to quality and precision. With our strict testing procedures, you can rely on your incubator to deliver dependable results from day one.
Repair and Refurbishment Protocol for Used Laboratory Incubators Performance and Quality from American Instrument Exchange
At American Instrument Exchange, every used laboratory incubator we sell goes through a repair and refurbishment protocol. Whether it’s a standard, CO₂, or refrigerated incubator, our goal is to restore each unit to laboratory-level performance—ensuring temperature accuracy, environmental stability, and long-term reliability in your lab.
Why Choose a Refurbished Laboratory Incubator from American Instrument Exchange?
• Fully tested for performance and safety
• Backed by a warranty
• Cost-effective alternative to new equipment
• Environmentally sustainable through reuse and restoration
• Refurbished by expert technicians with decades of lab equipment experience
Step-by-Step Refurbishment Protocol
Every incubator at American Instrument Exchange follows this comprehensive, multi-stage process:
1. Initial Intake & Inspection
• Visual inspection for cosmetic wear, corrosion, dents, or broken components
• Mechanical assessment of door hinges, gaskets, seals, and chamber components
• Document any missing parts or issues requiring repair or replacement
2. Cleaning and Decontamination
• Thorough internal and external cleaning using non-abrasive solutions
• Decontamination/cleaning of surfaces to remove biological, chemical, or particulate residue
• Cleaning of removable parts (e.g., shelves, trays, etc.)
3. Mechanical and Electrical Repair
• Repair or replacement of worn mechanical components such as door latches, fans, hinges, and seals
• Evaluation and repair of control panels, switches, thermostats, and displays
• Inspection and testing of wiring, fuses, relays, and power supplies
4. Environmental Control System Assessment
• For CO₂ incubators: CO₂ sensors, regulators, and gas delivery systems are tested
• For refrigerated incubators: compressors, condensers, and cooling systems are evaluated for performance and leaks
• Fan motors and airflow systems are tested to ensure uniform environmental conditions
5. Temperature and Sensor Testing
• All temperature sensors and controllers are tested using thermometers/probes
• Uniformity and accuracy tested at multiple chamber locations
• For humidified or CO₂ incubators, humidity and CO₂ stability are verified
6. Safety System Testing
• Test of over-temperature protection systems and alarms
• Evaluation of door sensors, safety interlocks, and power failure recovery
7. Final Quality Control and Documentation
• Full performance test run over 24 hours
• Validation of setpoints for temperature, CO₂ (if applicable), and humidity (if applicable)
• Final inspection and cleaning before packaging
• Complete service report
Trust the Experts at American Instrument Exchange
With over 50 years in the lab equipment industry, American Instrument Exchange is a trusted source for high-quality refurbished laboratory incubators. Our proven refurbishment protocol ensures every unit is reliable, accurate, and ready to meet the demands of your lab from day one.
Warranty Information
All used equipment sold by American Instrument Exchange is refurbished/reconditioned, tested to meet specifications, cleaned, and comes with a 90-day warranty from the date of shipment unless otherwise specified. New products include a warranty from the manufacturer. Your warranty is only valid if you have paid your invoice. If your invoice is over 30 days old, warranty work will not be performed until your invoice is paid in full. American Instrument Exchange is not liable for any special or consequential damages that result from the use of, or the inability to use, the materials on this site or the performance of the products,
Exceptions include international sales and items that are agreed to be sold with a lesser warranty or items that are agreed to be sold “as is.”
Should there be visible shipping damage to packaging or concealed shipping damage to item(s) supplied, buyer must communicate such damage to the delivering entity or carrier upon receipt first and to American Instrument the same day item is accepted / signed for. Failure to do so voids warranty. Customer decision to involve / procure third party or OEM service other than American Instrument or AIE assigned vendors to resolve in-warranty instrument failure or defect without first placing a service call to American Instrument voids warranty.
Return & Cancellation Policy
American Instrument Exchange will authorize the return of and issue a full refund for any equipment that is not working as represented and could not be replaced or repaired to the customer’s satisfaction by AIE or a representative of AIE during the warranty period. Returns without prior authorization and an RMA number will not be accepted.
Customers are responsible for proper packaging of the equipment and all included accessories. American Instrument will pay for insurance and shipping costs. Non-inventory items bought specifically to fill customer orders may possibly be returned, but on a case by case basis.
Customers who cancel orders after refurbishing has begun or after delivery where there are no equipment performance issues may be subject to a Restocking/Cancellation Fee of 20% or more and responsible for shipping costs for both the delivery and return.
Ongoing and Extended Support Options
American Instrument Exchange is able to provide additional repair and support services outside the warranty terms for most products that sell.
For biosafety cabinets, clean benches, chemical fume hoods, and other clean air products our team at AIE Laboratory Services can provide certifications, repairs, decontaminations, and other services for customers throughout New England, and guidance and limited technical assistance for any customers in the US and Canada for new or refurbished biosafety cabinets purchased from American Instrument Exchange.
For all other products, the repair service team at American Instrument Exchange can provide both field and depot repair evaluations. We can easily schedule and coordinate the pick-up and transportation of your malfunctioning equipment. By offering hourly rates lower than most OEM service providers and eliminating travel time for technicians, we help reduce repair costs. Furthermore, our lab depot repair service minimizes or eliminates scheduling delays. Our experienced service technicians are qualified to restore your equipment to factory specifications.
Yes, all equipment from American Instrument Exchange comes with a warranty. Used/reconditioned/refurbished equipment is tested to make sure it operates to the manufacturer's specifications and comes with a 90-day warranty (unless otherwise noted). New equipment comes with a warranty from the manufacturer.
How do you test and recondition the equipment?
Testing requirements vary across all the equipment categories we sell. Temperature controlled units are tested with NIST traceable probes and data loggers. Gaskets, external housing, glass, handles, controls and control screens are all thoroughly inspected for integrity and functionality. We test all equipment using the manufacturer's parameters and specifications to confirm that the unit operates properly.
How do products ship from American Instrument Exchange?
We can ship products both nationally and internationally using a well-established network of transporters. Smaller items will ship via UPS. Larger equipment will be palletized and shipped either LTL or air-ride, depending on the specific equipment and/or delivery requirements.
Return and order cancellation policy
American Instrument Exchange will accept the return of any product that is not working as represented and could not be replaced or repaired to the customer's satisfaction during the warranty period. Customers who cancel orders after refurbishing has begun will be subject to a cancellation and restocking fee of between 20% and 40%.
Are discounts available for educational or non-profit institutions, or for bulk purchases?
Yes – call or email us today with a list of equipment you're looking for and we can potentially put together a quote that includes a discount.
How does your price matching policy work?
We strive to keep our pricing competitive and reasonable. If you find comparable items for sale at a lower price from other vendors please send us a link and or quote for the item and we'll do our best to match or beat the price.
Can I see the equipment in person before committing to a purchase?
Customers are welcome to make an appointment to view equipment in our warehouse. Given our workload we may not be able to test or clean the equipment prior to your arrival if you have not committed to an order.
1023 Western Avenue is a working warehouse, not a showroom, and customers should dress appropriately and wear closed toe shoes.
Can I ship products that I purchased elsewhere to American Instrument for repair?
Yes – please see our repair services page for more information.
